Indoors & around the home
Electricity and natural gas power our appliances, and heat and cool our home. Learn how to operate your equipment and appliances safely.
Natural gas service disruption
When natural gas service is disrupted, we relight crucial customers like hospitals and senior centres first, and then all other customers. Although disruptions are usually short-lived, complex repairs to a gate station (where natural gas pressure is reduced and distributed) or pipeline may mean your service will be out for several hours.
Natural gas furnaces do not have to be turned off. They should operate normally when the power is restored.
Ensure wood-burning fireplaces and stoves are properly ventilated, and there is no risk of carbon monoxide build-up.
Do not use portable fuel-burning equipment (for example, generator, patio heater, barbecue) inside your home or garage.
Keep your natural gas meter clear
Snow and ice on your natural gas meter can create a build-up on the regulator. This can block the vent and allow excess gas pressure into your home, or put stress on the meter piping and cause a gas leak.
Inspect your furnace and venting system every year.
- Ensure proper air circulation around your furnace by keeping it clutter-free.
- Keep combustible materials (for example, paper, chemicals, paint, cleaning products) away from your furnace.
- Never use gasoline or other flammable vapours or liquids near your natural gas furnace or water heater.
- Check the flame of all natural gas appliances regularly – it should be blue. A yellow flame may be a sign of carbon monoxide.
Surge protection and GFCIs
A surge suppressor limits the amount of electricity during a power surge and may protect your electrical devices. A licensed electrician can install a surge suppressor at your main service panel. Add point-of-use surge suppressors such as power bars or plug-in types as well.
- A surge suppressor will not protect your equipment from a direct lightning strike.
- Unplug your computer if you are not going to use it over an extended period.
A ground fault circuit interrupter (GFCI) cuts off power to an appliance if a loss of current is detected. Install GFCI outlets where electric appliances may come into contact with water (for example, bathrooms, kitchens, patios).
- GFCIs are required by code in new homes but can be installed in older homes.
- Lightning and power surges can damage a GFCI’s circuitry.
- Follow manufacturer’s instructions and test GFCI outlets monthly.
Extension cords and outlets
Overloaded outlets and damaged extension cords can cause electrical fires. Extension cords should be used only as a temporary connection. If permanent wiring is required, have a licensed electrician install more outlets.
- Do not plug more than 1 major appliance into an outlet.
- Childproof your electrical outlets if young children are in your home.
- Keep outdoor wall receptacle covers closed when not in use.
- Keep the cord fully extended while in use to avoid overheating.
- Do not run a cord under a rug.
- Do not handle a cord in the rain or if you are barefoot on a wet surface.
- Use a cord long enough for the job – do not link cords together.
Keep your work area dry. Dampness and electricity can give you a fatal shock. Use a double-insulated power tool or a ground-fault circuit interrupter (GFCI) to reduce the risk of shock.
- Turn off the tool before you handle its plug to avoid accidental start-ups.
- Plug a power tool with a grounded cord cap into a grounded outlet.
- Unplug a power tool that has fallen into water before you touch it.
Natural gas lines may intersect with sewer service lines outside your home or business. These intersections are called cross bores. Damage to the cross bore can result in a natural gas leak, fire, or explosion.
The sewer must be inspected before you attempt to clear it with rotating equipment or water jets. Even if your home does not use natural gas, pipelines can be nearby. If the inspector does not find any evidence of a cross bore, they will tell you to proceed.
If there is a chance of a cross bore we will correct the situation so the sewer clearing can be completed safely.
You do not need to call if you or your plumber are:
- fixing the problem within the walls of the building;
- doing a video inspection to check if there is a cross bore;
- attempting to clear a blockage with plungers or push rods.
Did you find what you were looking for? Send us your feedback.